2015 Ford Focus Transmission Control Module: Symptoms, Cost and Fix for 2026
A failing 2015 Ford Focus transmission control module is one of the most common reasons a DPS6 automatic Focus shudders, loses drive, or refuses to start. The module is the computer that tells the dual-clutch transmission when to shift, and when its internal circuits fail, the transmission stops listening. The fix is a replacement module plus programming and a clutch adaptive learn. A dealer job usually totals $1,200 to $1,800, while a DIY job can be as low as $275 to $350. Ford’s extended TCM coverage under program 14M02 has expired for essentially every 2015 car (coverage runs 10 years from the warranty start date, so check your VIN), so check the warranty first, confirm the fault with a scan, and do not pay for a clutch until the codes say the clutch is the problem.
7 Signs Your 2015 Focus TCM Is Failing
One symptom alone proves little, but two or three together point straight at the module.
| Sign | What you notice | How urgent it is |
|---|---|---|
| Shuddering on takeoff | A shake as you pull away, worse in traffic | Scan soon |
| Delayed engagement | You select Drive or Reverse and nothing happens for a beat | Scan soon |
| Loss of drive | The car suddenly loses power while driving | Tow it |
| No-start | The engine runs but the transmission will not engage | Tow it |
| Limp mode | The car limits speed or gears, often with a warning | Tow it |
| Flashing gear display | The PRNDL indicator flashes, or a hill-start warning appears | Scan soon |
| Battery drain | Owners report the module can fail to sleep and drain the battery overnight | Scan soon |
Shuddering deserves a careful read. A worn clutch shudders too, so shudder alone does not condemn the TCM. The signs that point at the module are the electrical ones: no-start, loss of drive, a flashing gear display, and warnings that appear and clear on their own. Intermittent faults are a classic TCM signature because a cracked solder joint works when it is cold and fails as it heats up. Our guide on how a Ford shudder gets diagnosed explains why a dealer starts with a scan instead of guessing at parts.
Owner complaint data backs up the pattern. CarProblemZoo records 719 Focus automatic transmission control module problems, including a 2015 Focus that lost reverse and was diagnosed with a failed TCM at 56,990 miles.
What the 2015 Focus TCM Does Inside the DPS6
This section applies to one configuration only: a 2015 Focus with the 2.0L Duratec engine and the DPS6 PowerShift 6-speed dual-clutch automatic, Ford’s internal code 6DCT250. A 2015 Focus with the 1.0L EcoBoost uses the 6F15 conventional automatic instead, so none of the part numbers or programs here apply to that car.
The DPS6 is not a conventional automatic. It is an automated manual with two dry clutches and no torque converter. One clutch handles gears 1, 3, and 5, and the other handles reverse, 2, 4, and 6. The TCM drives the two clutch actuator motors, times every shift, and talks to the powertrain control module (PCM) about engine speed and load. If you are unsure which transmission your car has, our Ford transmission identification chart shows how to tell them apart.
The module mounts on the transmission case in the engine bay, on the driver side near the firewall and battery area. Constant heat cycles and vibration degrade the solder joints and pin connections on early modules, which is why Ford redesigned the unit as the K05 revision.

TCM or Clutch? 5 Tests That Tell Them Apart
This is the decision that saves or wastes the most money on a 2015 Focus. A clutch job costs $1,800 to $3,200, and a TCM job costs far less, so guessing wrong is expensive.
TCM or Clutch? 5 Tests That Tell Them Apart
2015 Ford Focus with the DPS6 PowerShift automatic. Work through the tests in order before you order parts.
Scan for codes
P0606, U0100, U0101, U1013, U3003, or P2832 stored means the TCM. P07A3 or gear ratio codes, or no TCM codes at all, means the clutch.
Watch the gear display
PRNDL flashes or warning messages appear means the TCM. A normal display while the car shudders means the clutch.
Check when it fails
Faults that come and go, often worse when hot, mean the TCM. A steady shudder that grows with mileage means the clutch.
Try a restart
A restart that clears the fault for a while means the TCM. A restart that changes nothing means the clutch.
Inspect seals for leaks
No visible leak means the TCM. A leaking input shaft seal or a worn clutch means the clutch.
The verdict
Fix the TCM first when its codes are present. Ford TSB 16-0129 says to replace the module for P0606 and the U0100/U0101/U1013/U3003 codes. A clutch job costs $1,800 to $3,200, and a dealer TCM job costs $1,200 to $1,800. Program 14M02 covered the TCM for 10 years or 150,000 miles, but it has expired for a 2015 car.
| Test | TCM failure points this way | Clutch failure points this way |
|---|---|---|
| 1. Scan for codes | P0606, U0100, U0101, U1013, U3003, or P2832 stored | P07A3, gear ratio codes, or no TCM codes |
| 2. Watch the gear display | PRNDL flashes or warnings appear | Display stays normal while the car shudders |
| 3. Check when it fails | Faults come and go, often worse when hot | Shudder is steady and grows with mileage |
| 4. Try a restart | A restart clears it for a while | A restart changes nothing |
| 5. Inspect seals for leaks | No visible leak around the input shaft seal or case | Leaking input shaft seal or worn clutch |
If the scan shows P0606 or a U0100/U0101 communication code, fix the module first. Ford’s service bulletin for these codes says to replace the TCM, and a new clutch will not fix a computer that cannot command the clutches. If the scan shows no TCM codes and the shudder is constant, the clutch is the more likely fault. Before ordering parts, have the codes read for free at a parts store and inspect the input shaft seal area and the transmission case for leaks. The DPS6 is a sealed unit with no transmission dipstick, so there is no owner-serviceable fluid check; a shop checks the level at the fill plug.
4 TCM Trouble Codes That Condemn the Module
A code reader turns a guess into a diagnosis. These four matter most for a 2015 Focus TCM, and Ford’s bulletin 16-0129 ties the first group to module replacement.
P0606: TCM internal processor failure. This is the code that condemns the module. It means the module’s own self-check found an internal fault.
U0100, U0101, U1013, and U3003: lost communication with the TCM. These codes mean the PCM cannot talk to the module, or the module drops off the network. TSB 16-0129 covers 2012-2016 Focus and 2011-2016 Fiesta cars with the DPS6, and its procedure is blunt: if U0100, U0101, U1013, U3003, or P0606 are present, replace the TCM, then reprogram the PCM and TCM with the latest calibrations using Ford IDS release 102.01 or higher. Ford published the full TSB 16-0129 procedure with the symptom list and the step-by-step check.
P2832: shift fork A position circuit. This code means the module cannot read or drive shift fork A, which serves gears 1, 3, and 5. The listed causes are an outdated TCM program, a faulty TCM, or a faulty transmission assembly, so the first step is a reflash and a retest before any parts are ordered. A related input speed code, P0715, can appear alongside TCM faults, and our P0715 sensor location guide shows where that sensor sits.
P07A3: friction element A stuck on. This code means clutch A is not disengaging. The causes include a faulty clutch, a damaged clutch lever or bearing, a failed actuator motor, or a defective module.
2015 Ford Focus TCM Replacement Cost in 2026
Prices vary by channel, so confirm the out-the-door price, including any core charge, before you order.
| Cost item | Typical range | Notes |
|---|---|---|
| New OEM TCM from a dealer | $400 to $600 | Latest K05 revision if available |
| Dorman OE FIX remanufactured 609-231 | $512 to $1,192 | List vs jobber price; core $200 to $350 |
| Used or salvage module | $100 to $200 | High risk; may already be failing |
| Programming and adaptive learning | $100 to $250 | Required even for pre-programmed units |
| Dealer labor for the swap | $150 to $400 (estimate) | Roughly 1 to 2 hours plus diagnostics; varies by shop and region |
| Full dealer job, parts and labor | $1,200 to $1,800 | The most commonly quoted all-in figure |
| DIY with a programmed aftermarket module | $275 to $350 | Your labor plus a scan tool session |
The Dorman 609-231 deserves a close look because it is the most widely stocked aftermarket option. AutoZone lists it at $1,191.99, Advance Auto Parts lists it from $909.99, and a technician thread on diag.net reports about $512 plus a core charge at jobber pricing. The spread is the difference between list price and trade price. Dorman’s OE FIX version uses soldered connections on the critical pins instead of the compliant pin connections that fail on the original module. The AutoZone Dorman 609-231 listing shows the price and the OE FIX description. Ford’s original module is AE8Z-7Z369-F, and the K05 revised module is AE8Z-7Z369-K, so ask for the K05 revision by name and check the label before the module goes in the car.
How to Replace the 2015 Focus TCM in 7 Steps
A competent DIY owner can usually complete the mechanical swap in an hour or two, before programming. The programming is the part you cannot skip, and it is what sends most owners to a shop.
- Disconnect the battery. Remove the negative terminal first and wait a few minutes so no live circuits are present while you handle the module connectors.
- Remove the air intake box. The TCM sits under it on the driver side of the transmission, near the firewall. On some cars the battery tray also comes out for clearance.
- Unplug the electrical connectors. Release the lock levers and pull the connectors straight off. Inspect the pins for corrosion or green deposits before fitting a new module.
- Remove the mounting bolts. Two or three bolts hold the module to the transmission case. Keep them, since the new module may not include hardware.
- Fit the new module. Check the part number on the label first and confirm it is the K05 revision. Seat the sealing gasket, tighten the bolts evenly, and reconnect the connectors until the lock levers click.
- Refit the airbox and reconnect the battery. Double-check that no tools are left loose in the engine bay.
- Program the module and run the adaptive learn. This is mandatory. Program the new TCM with Ford IDS or a compatible tool such as FORScan, then run a clutch adaptive learn so the module learns the clutch touch points. A pre-programmed module still needs the adaptive learn.
Drive gently for roughly the first 20 to 30 miles after the learn so the module gathers clean data. Our transmission adaptive learning reset guide explains what the learn does.

Is Your 2015 Focus Still Covered? 14M02 Expired in 2025
The short answer is no, and that is the most important fact in this article for a 2015 owner. Ford’s Customer Satisfaction Program 14M02 extended DPS6 TCM coverage to 10 years or 150,000 miles from the warranty start date, covering 2012-2016 Focus cars built between August 1, 2010 and November 5, 2015 at Michigan Assembly. For cars already past the time or mileage limit, Ford offered a one-time TCM replacement through June 30, 2025. That deadline has passed, so a TCM failure today is an out-of-pocket repair. Program 14M01 is the separate clutch program, covering the clutch assembly, input shaft seals, and software calibration to 7 years or 100,000 miles. Some secondary sources swap the two program numbers, but the Vargas v. Ford settlement defines them the same way.
Ford issued recall 26S40 in June 2026, and some owners confuse it with TCM coverage. It is not a TCM recall. It covers about 255,000 to 258,000 model-year 2012-2018 Focus cars whose 2018 recall 18S32 software remedy for a sticking canister purge valve may not have been installed correctly, and the remedy is a free PCM software update. The NHTSA recall report for 26V369 confirms the defect is the purge valve, not the transmission module.
To confirm your own coverage status, run your VIN through Ford’s recall and program lookup and read our guides on the Ford factory warranty and how to check Ford warranty coverage. Ask the dealer to check OASIS for open field service actions, and mention 14M02. The CarTipsDaily warranty extension guide lays out the 14M02 terms and the June 30, 2025 deadline.
5 Questions to Ask Before You Pay for a TCM
- What codes are stored? If the answer is P0606 or U0101, the module is the fault. If there are no TCM codes, ask why the module is being blamed.
- Is it the K05 revision? Confirm the part number AE8Z-7Z369-K on the quote. An early-revision module is a repeat failure waiting to happen.
- Does the quote include programming and the adaptive learn? A quote that omits them is incomplete. Budget $100 to $250 for this step.
- Was the clutch checked? A leaking input shaft seal contaminates the clutch and causes the same shudder.
- Is any Ford coverage still open? Ask for an OASIS check on 14M02 and any open field service actions before you pay anything.
If the car is worth less than the repair, weigh the fix against the value. Kelley Blue Book’s Fair Purchase Price for a 2015 Focus in typical condition is about $5,400 to $7,225 depending on trim (checked November 2026), so a $1,200 to $1,800 dealer TCM job is still a large share of the car’s value. If the clutch is also worn, the combined bill can pass $3,000, and at that point selling the car deserves a serious look. For a broader view of whether the car is worth keeping, read our Is Ford Focus a Good Car guide.
5 Questions Owners Ask About the 2015 Focus TCM
How do I know if my 2015 Focus TCM is bad?
The clearest signs are a P0606 code, a U0101 lost-communication code, intermittent loss of drive, a no-start with a running engine, or a flashing gear display. Shudder alone is not enough.
How much does it cost to replace a 2015 Ford Focus TCM?
A new OEM K05 module costs $400 to $600, a Dorman remanufactured 609-231 costs $512 to $1,192 depending on the retailer, and programming adds $100 to $250. A full dealer job usually totals $1,200 to $1,800.
Does a new TCM need programming?
Yes. Every replacement TCM must be programmed to the car and put through a clutch adaptive learn with Ford IDS or a compatible tool. A pre-programmed unit still needs the adaptive learn.
Where is the TCM located on a 2015 Ford Focus?
It mounts on the transmission case in the engine bay, on the driver side near the firewall and battery area, under the air intake box.
Is the 2015 Focus TCM still under warranty?
No. Program 14M02 covered the TCM for 10 years or 150,000 miles, and the one-time replacement offer for cars past those limits expired on June 30, 2025.
Your Next Step With a Failing 2015 Focus TCM
Start with a scan, not a parts order. If the codes are P0606, U0100, U0101, U1013, or U3003, the module has failed, and the fix is a K05-revision replacement plus programming and a clutch adaptive learn. If the codes point at the clutch, fix the clutch instead. Check your VIN for open Ford programs before you pay, confirm the part number on the quote, and make sure programming is included in the price. A 2015 Ford Focus transmission control module is a known weak point with a known fix, and once the revised module is in and learned, the car should shift the way it did when it was new.
