Ford E350 Rear Blend Door

The blend door on a Ford E350 is located on the rear of the vehicle.

If you own a Ford E350 van, you may have noticed that the rear blend door may not be working properly. This can be a very annoying problem, as it can cause the rear of the van to be much warmer or cooler than the front. Luckily, there is a way to fix this problem without having to replace the entire door.

The first thing you will need to do is to remove the door panel. This can be done by unscrewing the screws that hold it in place. Once the panel is removed, you will be able to access the blend door itself.

In most cases, the problem with the door is that the actuator is not working properly. The actuator is responsible for opening and closing the door, and if it is not working properly, the door will not be able to move. You can usually tell if the actuator is the problem if the door is stuck in one position or the other.

To replace the actuator, you will first need to remove the old one. This can be done by unscrewing it from the door. Once the old actuator is removed, you can then install the new one. Make sure that it is screwed in securely so that it does not come loose.

After the new actuator is in place, you can then put the door panel back on. Screw it in place, and then test the door to see if it is working properly. If it is,

Where Is The Rear Blend Door Located On A Ford E350?

The rear blend door is located on the Ford E350 between the rear seat and the rear window.
If you’re having trouble with the rear blend door on your Ford E350, you’re not alone. Many Ford owners have reported this issue. The good news is that it’s relatively easy to fix, and you can do it yourself in about an hour.

Here’s a step-by-step guide to finding and fixing the rear blend door on a Ford E350:

1. Open the glove box and empty it out.

2. Remove the glove box liner by unscrewing the two screws that hold it in place.

3. Locate the rear blend door actuator. It’s a small motor located behind the glove box, on the left side of the vehicle.

4. Unplug the electrical connector from the actuator.

5. Use a ratchet or a wrench to remove the two bolts that hold the actuator in place.

6. Remove the actuator and set it aside.

7. Locate the rear blend door. It’s a small flap located behind the glove box, on the left side of the vehicle.

8. Use your fingers to move the door up or down, until it’s in the desired position.

9. Reinstall the actuator, and reconnect the electrical connector.

10. Screw the two bolts back in place.

11. Replace the glove box liner, and screw it back in place.

12. Put the items back in the glove box, and close it.

You’ve now fixed the rear blend door on your Ford E350. Congratulations!

How Do You Replace The Rear Blend Door On A Ford E350?

To replace the rear blend door on a Ford E350, remove the screws that hold the door panel in place, then remove the door panel and the broken door.

If you’re driving a Ford E350, then you know that it’s a workhorse of a vehicle. But like all vehicles, it’s not immune to wear and tear—and one of the parts that may eventually need to be replaced is the rear blend door.

The rear blend door is responsible for controlling the amount of hot and cold air that comes through the vents into the cabin. Over time, the door can become bent or damaged, which can cause the air to become imbalanced. If you’re notice that the temperature in your E350 is not what it used to be, then it may be time to replace the rear blend door.

Here’s a step-by-step guide on how to do just that:

1. Start by removing the screws that are holding the plastic cover in place on the inside of the vehicle, just behind the glove box.

2. Once the cover is off, you’ll be able to see the rear blend door.

3. Use a flathead screwdriver to remove the two screws that are holding the door in place.

4. Carefully remove the door and set it aside.

5. Take the new door and line it up with the opening.

6. Use the screws to secure the new door in place.

7. Replace the cover and screw it back into place.

8. Test the new door by turning on the heater and AC to see if the temperature is balanced.

That’s it! You’ve now successfully replaced the rear blend door on your Ford E350.


What Is The Purpose Of The Rear Blend Door On A Ford E350?

The rear blend door on a Ford E350 is used to control the amount of air that flows through the rear vents. The door is opened and closed by a motor that is controlled by the climate control system. When the door is open, air can flow through the vents and into the cabin. When the door is closed, the air is redirected to the front of the vehicle.

What Are The Symptoms Of A Faulty Rear Blend Door On A Ford E350?

There are a few symptoms that may indicate a faulty rear blend door on a Ford E350. These can include strange noises coming from the rear of the vehicle, unusual smells, and decreased airflow from the rear vents. If you notice any of these issues, it’s best to take your vehicle to a mechanic or dealership for diagnosis and repair.

I hope that you understand now. If you have any questions, please feel free to comment below.

David Jon

David Jon

I'm a long-time Ford and automotive enthusiast, and I've been writing about cars for over 10 years. I started Fordmasterx as an effort to combine my two passions – writing and car ownership – into one website. I hope that you find everything you need on our website and that we can help guide you through all your automotive needs.

We will be happy to hear your thoughts

Leave a reply